roof, roof contractors, roofs, rubber roofs

Rubber Roofs Torched Downs

Prepare the roof deck for membrane roofing by removing the old roofing material down to bare decking . Look closely for signs of deterioration . Replace deteriorated decking. For a smooth surface, cover there roof with a new layer of high density fiber board ( sold at roofing materials suppliers ) . Secure with fasteners recommend by the manufacturers for this purpose usually long scores with large insulation plates.

Sweep the roof deck thoroughly and spread out the membrane so it has a chance to relax . Make any cutouts in the membrane that may be necessary to allow for the vents pipes or other protrusions . Overlap the sheets 3 inches and wipe them down with the recommended cleaner ro prepare the surfaces for adhesive.

Apply the latex adhesive . Fold half of the first membrane sheet over on itself to expose the roof deck, and roll a heavy coat of adhesive onto both the deck and membrane surfaces with a medium nap paint roller . However , do not apply adhesive begins to set 9 about 20 minutes in normal conditions ), carefully roll the fold rubber down into place. Avoid wrinkling the membrane.

Use a stiff bristle push broom to brush out any air pockets that may be evident under the bonded half of the membrane . Brush from the middle of the roof outward to the edges. Then fold the other unbounded half over, apply adhesive to the rubber and roof deck again, and adhere this half of the membrane to the roof . Apply all sections of the membrane to the roof deck in this fashion , but do not apply adhesive within 3 inches of the edges of any overlapping sections rubber ; these must be accessible for applying seaming tape along the seams .

Roll the top section of overlapping membrane back along the seam area, and chalk a reference link inches from the edge of the bottom membrane . This mass the area for applying seam tape.

Tape the seams . Use the recommend cleaning solvent clean both halves of the overlapping membrane in the tape areas, then apply seaming tape sticky side down to the bottom membrane within the marked area. Press the tape down firmly to ensure good adhesion to the membrane.

Fold the top membrane overlap back in place on the tape. Slowly pull off the tape’s paper backing with the treatment edges now overlapping. Press the overlapping edges down to create a tighter , smooth seam. Roll the seamed areas with a J-roller or seam roller tool to bond the seam.

If the roof meets a vertical wall , you may need to remove siding so you can bond the membrane to wall sheathing . Use contact adhesive to apply the membrane 12 inch up the wall. Seal the edge with a metal termination bar fastened to the wall with exterior scores. Train off overhanging membrane around the roof edges , and flash it according to the manufacture’s recommendations using rubber adhesive flashing and rubber boots.

roofs

Roofing 3 Tab- Shingles

If you want to install asphalt shingle on your roof , the your are in good company . Asphalt shingles, are the roofing of choice for nearly four out of five homeowners in America . They perform well in all types of climate , are available in a multitude of colors, shapes, and textures to complement every housing design , and are less expensive than most other roofing.

Asphalt Shingles are available as either fiberglass shingles or organic shingles . Both types are made with asphalt, the difference being that one uses a fiberglass reinforcing mat, while the other uses a celluloses-fiber mat. Fiberglass shingles are lighter , thinner , and have higher tear strength , are more often in northern regions. Although the roofing market has exploded with innovative new asphalt shingle designs, such as innovative new asphalt shingle design designs, such as the architectural or laminated shingle that offers a three dimensional look , the standard three tab.

Stagger shingles for efective protection against leaks . If the the tab slots are lined in successive rows, water form channels, increasing erosion of the mineral surface of the shingles . Creating 6 inches off set between rows of shingles with the three tab shingles shown above ensures that the slots do not align.

Tools need

Aviation snips , Carpenter s square, Chalk line, Roofers hatchet , utility knife , Straight edge , Tape measure , Chalk gun , flashing, Nailing cartridges, roofing cement, roofing nails, 7/8 or 1 1/4. Rubber gasket nails , Protective equipment .

Cover the roof with felt paper after stripping down to plywood. and drip edge. Snap chalk line onto the felt paper or ice guard up from thieves edge, to mark the alignment of the starter course . This will result in a 1/2 inch shingle overhang fro standard 12 inch shingles .

Apply the first full course with the tabs pointing down . Begin at the first shingles so it overhangs the rake edge by 3/8 and the eaves edge by 1/2. Make sure the top of each shingle is flush with the top of the starter course, following the chalk line. Trim the edge line .

Snap the chalk line from the eaves edge to the ridge to create a vertical line to again the shingles. Choose an area with no obstructions, as close though a slot or a shingle edge on the first full shingle course. Use a carpenter s square to establish a line perpendicular to the eaves edge.

Use the vertical edge line . Check the alignment , Fill in the shingles , when reach the obstruction snap another vertical reference as a guide , Shingle upward the eaves and train off the excess. Install shingles on adjoining roof decks . Trim off shingle material valley flashing using utility knife . Install shingles up the vent pipe and glue with a double bead cement along the bottom edge the flange.

Shingle to flashing to chimney , Pry out the lowest course of siding tuck flashing under the siding , Install step flashing and shingles go down . When reach the ridge cut the shingle like home plate – pentagon . Also install the ridge if needs to all new homes have ridges .

stucco

Stucco:Repairs and Build New

Although stucco is very durable , it can be damaged , and overtime if can crumble of crack . The directions given below work well for patching small areas less than 2 square feet. For more extensive damage, the repairs is done in layers.

Tools you may need for Do it yourselfers .

Caulk gun , Disposable paint brush, Putty knife, Mason ‘s Trowel, Square-end trowel, Hammer, Whisk broom, Wire brush, Masonry chisel, Aviations snips, Pry bar, Drill with masonry bit, Scratching tool, metal lath, metal primer, stucco patching or bags of stucco and brown scratch stucco, bonding adhesive, masonry paint, 1 1/2 , 15 # building paper , Self furring metal lath, masonry caulk, Tint, Metal stop bead , particle or respirator, protective equipment .

How to pack small areas the brush to clean away rust any exposed metal lath , then apply a coat of metal prime .

Apply premixed or cheaper make your batch which is cheaper.
Repair compound to the repair area, slightly over filling the hole using putty knife or trowel . Read manufacture’s directions or drying time is consistent with mixture which is very important for larger patches or working on entire new areas built.

Smooth the repair with a putty knife or trowel, feathering the edges to blend into the surrounding surface . Use a the original texture. :et the patch dry for several days, then touch it up with masonry paint .

Make a starter hole with a drill and masonry bit , then use a masonry chisel and hammer to chip away stucco in the respirator when cutting stucco . Cut sell furring metal lath to size and attach it to the sheath using roofing nails . Overlap pieces by two inches . If the patch extends to the base of the wall, attach a metal stop bead at the bottom .

To mix consistency is so important . Combine three parts sand , two parts portland cement , one part masonry cement. Add enough water so the mixture holds it in one hour . Tip; Premixed stucco works well for small jobs obviously not large jobs. Thats why mix for bigger jobs and requires skilled masonry and mixed laborer .

Apply 3/8 thick layer of stucco directly to the metal lath which called scratch coat . Push the the stucco into the mesh until it fills the gap between the mesh and the sheathing . Score the horizontal grooves into the wet surface using a scratching tool . Let the stucco dry two days, misting it with water every 2 to 4 hours .

Apply second of the stucco . Build up the stucco to within 1/4 of the original surface . Let the patch dry for two days , misting every 2 to 4 hours .

Combine finish coat stucco mix just enough water for the mixture to hold its shape . Dampen the patch area the patch area, then apply the finish coat to match original surface . Dampen the patch periodically for a week . Let it dry for several more days before painting .

Attics, Basement, decks, drywall, Foundation, HVAc, Kitchens and Bathrooms New, pavers, plumbing, Remodeling Kitchens and Bathrooms, roof, roof contractors, stucco, stuuco

Home Remodeling

Home Renovations

Tackling a large scale home remodeling project can be a daunting task. Although remodeling is often very rewarding , it is often very rewarding , it is usual a long , expensive process with many details to keep in mind , and having to coordinate the plans of several different contractors can be confusing and tiresome . Hiring a total home remodeling company can help alleviate some of the stress because all communications and planning is done with one company .

Keep an eye to detail of you want help move the process such pins is a good online ideas and cheap way out than an interior decorator , helps smooth process preparing for the remodel and save time .

Getting real budget
Before hiring a company , decide what kind of remodeling you want to have done and calculate whether or not you will have the funds readily available ( estimate locked in a proposal ) pay for it. Don’t become too attached to an idea prior to determining how much it will cost to implement ; it will be much harder to stay on budget if you refuse to compromise on design details. As long as you have a good general idea of what you would like done and how much you are willing to spend, many contractors will help you create a design that fails within your budget constraints .

Cleaning Preparation
Remodling can be an extensive ordeal , lasting from several days to several months, and properly preparations will save time. Many contractors will be able to move some larger items for you, but homeowners are typically responsible for cleaning out small things can get in the way or be damaged . Many room remodels include new cabinets or storage space, so remove everything from your your current cabinets before any work begins. If everything has been thoroughly cleaned and moved out of the way , the contractor will be able to get straight tow work .

Temporary Adjustments
With major renovations taking place in your home , it may not be ideal to spend a lot of time around the house.

Planning meals . If you are planning to remain in your home while your kitchen is being remodeled , you will have to find alternate place to eat and prepare food . For this reason , you may want to consider scheduling the remodel during a time when the weather is nice enough to eat outside if you own a grill and have an outdoor seating area . It can be also be helpful to set up a small , temporary food station in an unaffected room of the house with things like a coffee maker , some nonperishables, a mini refrigerators , and a toaster or min microwave . Also be sure to have plenty of paper plates and disposable cups and utensils on hand if you will not have access to a dishwasher .

Dealing with safety issues and pets and kids is safety contractors who are osha and IICRC certified is seal of protection of your kids and property .

Basement, Foundation, plumbing

This company is a major IICRC business firm and
construction and Basement systems foundation and water proofing repairs specialist. Established 1980 Top Job has manage the company worked major insurance companies and help get the money back without adjusters and insurance agents trying under bid or low ball the property damage assessment.

Uniforms are easily recognized what tech does water damage , mold damage , etc . Drug testing screen testing don’t use subtractors.

Testimonial

“Top Job Water Proofing came out dug a new sump pump plumbed the water go to pith off the house.
They did water proofing and worked on the foundation repair until it was fixed. ”

” They were easy to communicate with, and their work was excellent . They did foundation repair , and I would do work with them again for contractor
purposes in near future.

Causes of foundation problems issues
Foundation problems are most often caused by unstable soil or erosion. If one area under the house settles faster than another, stresses in the foundation and structure lead to cracks in the foundations, cracks in the internal walls, and sinking , buckling m or leaning foundations walls.

Fixing the problems

Underpinning . Installing underpins beneath the foundation to support the home’s weight is a common solution to foundation settlement problems. Access holes are dug around the house to expose the footing.
These holes are then used to set up a mold and pour a solid concrete block with reinforcement bars, or rebar, under the footing of the foundation.

Steel Piers
Installing steel piers under the foundation to support the structure’s weight is another typical solution . Common types of piers are helical piers and push or resistance piers. Helical piers are shaped like giants screws; the use of a hydraulic system , they are gradually screwed into the earth below the house until they reach either bedrock or load bearing soil . Special tools shift the weight of the house off the fill dirt and onto the piers. No force is applied to the house during installation . Push or resistance piers are also driven into the earth under the house until the they hit bedrock or load bearing soil . Plates are installed on top of the piers , and the home’s weight is shifted onto them .

Basement Wall
The pressure of the earth on the outside of a wall can cause problems with retaining walls and basement walls . A leaning , bowed , or cracked basement wall cannot effectively support the house above it.

Major structural commercial damage
Steel I Beams can be installed vertically against a severely bowed interior wall. They are either bolted to the floor slab or set into the exposed footing below the floor . The tops of the beams are then bolted to braces in the ceiling joists . Concrete or dry packing is installed above and below the point where the wall touches the beam.