Tag Archives: flood

Sump Pump French Drains Flood Basement

Sump Pump : Installing

If water continues to accumulate in your basement despite all your efforts at regrading and sealing your basement walls, installing a sump pump may be your inly option for resolving the problem . Permanently located in a pit that you dig beneath your basement floor, the sump pump automatically kicks in whenever enough water water accumulates in the pit to trigger the pump float. The water is then pumped out the basement through a pipe that runs through the rim joist of the house .

Because you will be digging well beneath the basement floor, make certain there is no sewer pipe or water supply in the digging area . Contact a plumber if you do not know for sure that the area is clear.

The purpose of a sump pump is to collect and eject water that accumulates beneath your basement floor ( usually due to a high water table ) before it can be drawn or forced up into the basement . The most effective sump installation have drain tile running around the entire perimeter of the house and channeling water to the pump pit. This system can be created as a retrofit job, but it is a major undertaking best left to a pro .

A submersible sump pump installed in a pit beneath a basement floor to [ump water out before it seeps up into the basement .

Install the pit liner after digging a hole for ti in the granular material under the floor . The hole should be a few inches wider than the liner . Remove the excavated material right away . Add gravel to the bottom of the hole as needed to bring the liner level with top of its rim at floor level.

Pack the liner in place by pouring 1/2 inch gravel around it. Add a 1 inch base of gravel and then mix concrete to patch the floor . Trowel the concrete around the rim with a float so the patch is level and smooth.

Prepare the sump sump installation . Thread a PVC adapter fitting onto the pump outlet , and then solvent glue a PVC stand pipe ti the adapter . the stand pipe should be long enough to extend about 1 foot past the liner rim rim liner rim when the pump is set on the bottom of the liner .

Attach a check valve to the top of the stand pipe to prevent the pump pit . Solvent weld another riser to fit into the top of the check valve and run upward to a point level with the rim joist, where the discharge tube will exit the basement .

Drill a hole in the rim joist for the discharge tube and finish routing drain pipe out through the rim joist.. Caulk around the tube on both the interior and exterior sides. On the exterior , attach an elbow fitting to the discharge tube and run drain pipe down from the elbow. Place a splash block beneath the drain pipe to direct water away from the house . Plug the pump in a GFCI-protected receptacle .

Things you may need also is to dry lock basement walls for leaks especially in July less of a water table. Regrade french drains and dirt outside dig trench ten feet away outside and dig a trash can size hole. Than place another receptacle with perforated holes and gravel place around , and let the water run off and away. 100 percent do the trick . Call topjobrestoration.com for any answers.

Drain Plumbing Water Damage Clean up Sewage Back up Problems

Drain problems causation and trouble shooting

What could cause gurgling in a rarely used wet-bar sink when water drains in the kitchen at one end of the house or in a bath at the other end? Chances are that the wet bar isn t vented or that its vent stack is blocked. You could check by looking for a plumbing vent pipe protruding through the roof above the area. It will look like the ones above kitchen and bath.

Sluggish drainage is one symptom of this problem. Sewer smell is another . When water drains in the kitchen or bath , it siphons water out of the wet bar s drain trap , which produces a gurgling noise. Without the seal provided by water in the drain trap , sewer gas can rise up through the sink and into the house .

If you don t use the wet-bar sink because of these problems , call a plumber to install an auto-vent. With this in place, the other drains won t siphon water out the trap. If you don t use it and don t really want it , have the plumber remove it and close the drain connection . In the meantime you can reduce the sewer gas smell by periodically pouring some water in the wet bar drain to keep the trap full.

Big Backups

Even with vapor venting, trap placement , and pipe sizing , drains still may be slow. This indicates a big blockage farther down the line. The best indicator that a blockage is in the waste line is sewage gurgling up through floor drains and basement fixtures. Solving this problem depends on your septic system type.

If you have a septic system with a leach field , your septic tank may need to be pumped out . This is a job for professional, but it s important to be around when the pumping concludes . Ask the pump operator if the tank was filled with enough greasy scum to cause the drain problems. If not , the pipes in the leach field itself may be the problem . Digging them up may be the only solution .

If your tied into a municipal sewage system , check to see whether any work has been done on your branch line lately . If so , it could have caused problems with your drainage , If not, tree roots may have gotten in the pipes . Hire a professional to auger the line and pull out the tree roots; thereafter , flush copper sulfate root treatment through the line twice year .

Do it yourself

There is snaking the kitchen line , clean out the pop up drain plugs hair clogged.. To access the trip waste linkage above the drain tub. If you cant get your toilet unclogged may have to remove the toilet snake it apply a new wax ring and reset it . Don t understand that process let a plumber handle it is just cheaper and safer, good luck.